-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
Recommended extras
Hand-picked recommendations to go alongside this product
Tap Features:
- Tap offers filtered cold water, domestic hot water and instant boiling water (up to 98°C) water
- Stylish knurled tap body
- A stunning vanto black boiling water tap with a variety of silicone tube colours to select from - adding flexibility and a bit of your personality to your tap
- Two patterned flexi spray for domestic hot & cold water - easily switch between a precise stream and a powerful spray for versatile kitchen tasks
- Pull out spout - reach those hard-to-clean areas of your sink
- Easy-to-use dual levers offering filtered cold water and domestic hot water from the right handle and 98°C water from the left
- Push and hold left-hand lever to avoid accidental use of 98°C water
- Tap body crafted from brass providing durability and antibacterial properties
- Minimum 1 bar water pressure
- Aerated spout mixes air into the water to give a soft, champagne-like flow
- Ceramic disc technology preventing excess dripping and leaking
- Supplied with flexitails to connect the tap to mains supply and boiler unit with ease
- Includes tap, tank and filter
- 5 year manufacturer’s guarantee
Boiler Features: - 4 litre tank suitable for even the busiest of homes
- Pre-set 98°C for an energy saving, continuous rolling boil
- Filter boasts an 80% reduction in chlorine at 2 parts per million over 28,000 litres - meaning you’ll be able to see and taste the difference
- Includes a vented system powered by a standard 13 amp plug
The filter has a 6 month lifespan - enough for 3800 litres of water. Replacement filters can be purchased separately, please see our recommended extras.
| Cleaning Instructions |
|---|
| Product Code | Tf-quilt-vblk-boil-tap-spouts |
|---|---|
| Type | Boiling Water Taps, Filtered Water Taps, Mono Kitchen Mixers, Pull Out Kitchen Taps |
| Brand | The Tap Factory |
| Brand Range | The Tap Factory Quilt |
| Guarantee Breakdown | Kitchen Tap: 5 year manufacturer's guarantee | Valves & Cartridges: 2 year manufacturer's guarantee | Boiler Unit: 2 year manufacturer's guarantee |
| GuaranteeMore information | 5 Years |
Guarantee
Please note that these guarantees are provided by the manufacturer, and will be subject to individual exclusions, exceptions, and terms and conditions, for example avoiding abrasive bleach-based cleaning products.
If you need further info about a specific manufacturer's guarantee, please contact our team.
| AeratorMore information | Yes |
|---|---|
| Material | Brass, Silicone |
| Cartridge TypeMore information | Ceramic Disc |
| Popular Features | Select an option first |
Tap aerators are simple but beautifully-engineered devices that save water and money without a perceived loss of pressure. These small attachments are inserted inside the end of the spout and provide a regulated, smoothed and aerated flow of water by separating a single flow into many tiny streams. These streams mix with air as they flow from the tap, meaning less water is needed to achieve the same 'feel' and performance as non-aerated taps.
They can also be purchased separately and retrofitted to most taps, or they can usually be uninstalled if not wanted. They're a great benefit on high pressure systems where the full flow of water is unnecessary, cutting your water bills and helping to reduce wastage. On lower-pressure systems they can help to improve the performance of a tap by adding air to the limited flow of water available. All-in-all, they're pretty awesome.
They can also be purchased separately and retrofitted to most taps, or they can usually be uninstalled if not wanted. They're a great benefit on high pressure systems where the full flow of water is unnecessary, cutting your water bills and helping to reduce wastage. On lower-pressure systems they can help to improve the performance of a tap by adding air to the limited flow of water available. All-in-all, they're pretty awesome.
Taps use either a ceramic disc cartridge or a rubber compression washer to control flow. Rubber washers will naturally wear down with use, and the tap handle will require more and more rotations to turn on or off. On the plus side, it's very easy to replace a rubber washer and they're available everywhere.
Ceramic disc cartridges need only a 90-degree rotation to fully open or close, and the 2 ceramic plates are incredibly hard-wearing and resilient. They're more expensive to make, but they allow for a huge range of designs, easy operation and simple maintenance if needed.
Whilst it is rare for a ceramic cartridge to need replacing, you may very occasionally need to remove and rinse the cartridge if grit or debris within the water system is preventing the 2 plates from closing properly. Much like replacing a rubber washer, this is a quick and easy job, and will ensure many years of use.
Ceramic disc cartridges need only a 90-degree rotation to fully open or close, and the 2 ceramic plates are incredibly hard-wearing and resilient. They're more expensive to make, but they allow for a huge range of designs, easy operation and simple maintenance if needed.
Whilst it is rare for a ceramic cartridge to need replacing, you may very occasionally need to remove and rinse the cartridge if grit or debris within the water system is preventing the 2 plates from closing properly. Much like replacing a rubber washer, this is a quick and easy job, and will ensure many years of use.
| Mounting Type | Deck Mounted |
|---|---|
| Shape | Round |
| Handle Type | Dual Control, Lever |
| Spout Type | Dual Function Spray Spout, Pull Out Spout, Swan Neck Spout, Swivel Spout |
| Tap Holes | Mono |
| Style | Modern |
| Finish | Select an option first |
| Texture | Select an option first |
| Minimum Tap Hole Size (mm)More information | 35 |
|---|---|
| Height (mm) | 482 |
| Depth (mm) | 220 |
| Projection (mm) | 220 |
This is the minimum recommended hole diameter that this tap needs for installation. Generally, the tap will sit on top of the sink or worktop, and the hot and cold water feeds and fixing bolts will need to slot through the tap hole and be connected underneath. Your hole can be a bit larger than this size, provided it is not larger than the diameter of the base of the tap.
| Flow Rate at 1 Bar (l/min) | 4.53 |
|---|---|
| Flow Rate at 2 Bar (l/min) | 6.54 |
| Minimum Water PressureMore information | 1 |
Minimum Water Pressure
Your water pressure depends on your home's water system. It’s important to consider water pressure when buying a new tap or shower. Buying a product with a minimum water pressure that’s too high for your home will result in poor performance.
- With a combi boiler you can usually expect between 1 and 2 bar
- With a gravity system (cold water tank in attic) you may have as little as 0.1 or 0.2 bar upstairs, and perhaps 0.5 bar downstairs
- With a high pressure unvented system (hot water cylinder, no cold water tank) you will generally have between 1 and 3 bar
You can install an item with a low minimum pressure rating on a high pressure system, but avoid installing an item with a high minimum rating on a low pressure system! Read our guide to water pressure to learn more.
Products from the same range
You may also like
Customers also bought
Related categories
We're here for you
Advice guides
-
These Are Our Favourite Kitchen Ideas 2023
Need some kitchen design inspiration? From choosing the perfect taps to new design styles, we take you through our picks for the top kitchen trends of 2023. -
Boiling Water Taps Guide
From water temperatures and pressure to cost and installation, we take you through everything you need to know about boiling water taps.
