-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
Recommended extras
Hand-picked recommendations to go alongside this product
This brushed gold boiling water tap will almost certainly become the pride and joy of your kitchen. Impressing everyone with its heat insulation technology that keeps the body of the tap cool, the Vellamo Kaffe provides pure near-boiling hot water at the click of a finger (well, turn of a tap). The Neoperl aerator ensures a splash-free experience and the child-safe spring lock means your mind can rest easy even with little ones around.
Tap Features:
Tap Dimensions:
Boiler Features:
Boiler Dimensions:
Tap Features:
- Made from high quality brass with a striking brushed gold finish
- Neoperl aerator - creates a soft, splash-free flow of water
- Heat insulation technology - keeps the spout cool to the touch, even when the steaming water is flowing
- Child safe spring lock technology - the handle must be pressed and turned at the same time to release steaming water
- 360° swivel spout - ideal for use with a 1.5 or 2 bowl kitchen sink
- Standard hot and cold water from an easy to use single lever
- Ceramic disc valves for improved performance & longer life span
- Minimum 1.0 bar water pressure required
- Comes with a carbon rod water filter - gives you pure near-boiling water
- Filter can be replaced in seconds - twist, pull and replace
- 2 year guarantee
Tap Dimensions:
- Overall height - 343mm
- Spout exit height - 257mm
- Projection - 210mm
Boiler Features:
- Delivers instantly hot filtered water - adjustable between 75°C-98°C
- Easy to use digital touch screen operation
- Unique unvented design eliminates the need for extra pipework and means no excess water is discharged to drain
- Fully insulated 2.4 litre boiler
- Holds enough water for up to 10 cups of tea or coffee at a time
- 4 minute re-boil time
- Brushed stainless steel surround and smoked glass top
- Float sensor detects water level in the tank to avoid damage to the unit
- Requires standard 220-240V 13 amp socket - no electrian required for installation
- No separate cold water supply needed to be plumbed in
- 2 year guarantee on the boiler unit
Boiler Dimensions:
- Height - 315mm
- Depth - 210mm
- Width - 210mm
Cleaning Instructions |
---|
Product Code | BTF005 |
---|---|
Type | Boiling Water Taps, Mono Kitchen Mixers |
Brand | Vellamo |
Brand Range | Vellamo Kaffe |
GuaranteeMore information | 2 Years |
Guarantee
Please note that these guarantees are provided by the manufacturer, and will be subject to individual exclusions, exceptions, and terms and conditions, for example avoiding abrasive bleach-based cleaning products.
If you need further info about a specific manufacturer's guarantee, please contact our team.
AeratorMore information | Yes |
---|---|
Cartridge TypeMore information | Ceramic Disc |
Tap aerators are simple but beautifully-engineered devices that save water and money without a perceived loss of pressure. These small attachments are inserted inside the end of the spout and provide a regulated, smoothed and aerated flow of water by separating a single flow into many tiny streams. These streams mix with air as they flow from the tap, meaning less water is needed to achieve the same 'feel' and performance as non-aerated taps.
They can also be purchased separately and retrofitted to most taps, or they can usually be uninstalled if not wanted. They're a great benefit on high pressure systems where the full flow of water is unnecessary, cutting your water bills and helping to reduce wastage. On lower-pressure systems they can help to improve the performance of a tap by adding air to the limited flow of water available. All-in-all, they're pretty awesome.
They can also be purchased separately and retrofitted to most taps, or they can usually be uninstalled if not wanted. They're a great benefit on high pressure systems where the full flow of water is unnecessary, cutting your water bills and helping to reduce wastage. On lower-pressure systems they can help to improve the performance of a tap by adding air to the limited flow of water available. All-in-all, they're pretty awesome.
Taps use either a ceramic disc cartridge or a rubber compression washer to control flow. Rubber washers will naturally wear down with use, and the tap handle will require more and more rotations to turn on or off. On the plus side, it's very easy to replace a rubber washer and they're available everywhere.
Ceramic disc cartridges need only a 90-degree rotation to fully open or close, and the 2 ceramic plates are incredibly hard-wearing and resilient. They're more expensive to make, but they allow for a huge range of designs, easy operation and simple maintenance if needed.
Whilst it is rare for a ceramic cartridge to need replacing, you may very occasionally need to remove and rinse the cartridge if grit or debris within the water system is preventing the 2 plates from closing properly. Much like replacing a rubber washer, this is a quick and easy job, and will ensure many years of use.
Ceramic disc cartridges need only a 90-degree rotation to fully open or close, and the 2 ceramic plates are incredibly hard-wearing and resilient. They're more expensive to make, but they allow for a huge range of designs, easy operation and simple maintenance if needed.
Whilst it is rare for a ceramic cartridge to need replacing, you may very occasionally need to remove and rinse the cartridge if grit or debris within the water system is preventing the 2 plates from closing properly. Much like replacing a rubber washer, this is a quick and easy job, and will ensure many years of use.
Mounting Type | Deck Mounted |
---|---|
Finish | Brushed Gold |
Shape | Round |
Handle Type | Lever, Single Control |
Spout Type | Swivel Spout |
Texture | Brushed |
Tap Holes | Mono |
Style | Modern |
Minimum Tap Hole Size (mm)More information | 35 |
---|---|
Height (mm) | 343 |
Projection (mm) | 210 |
This is the minimum recommended hole diameter that this tap needs for installation. Generally, the tap will sit on top of the sink or worktop, and the hot and cold water feeds and fixing bolts will need to slot through the tap hole and be connected underneath. Your hole can be a bit larger than this size, provided it is not larger than the diameter of the base of the tap.
Minimum Water PressureMore information | 1 |
---|
Minimum Water Pressure
Your water pressure depends on your home's water system. It’s important to consider water pressure when buying a new tap or shower. Buying a product with a minimum water pressure that’s too high for your home will result in poor performance.
- With a combi boiler you can usually expect between 1 and 2 bar
- With a gravity system (cold water tank in attic) you may have as little as 0.1 or 0.2 bar upstairs, and perhaps 0.5 bar downstairs
- With a high pressure unvented system (hot water cylinder, no cold water tank) you will generally have between 1 and 3 bar
You can install an item with a low minimum pressure rating on a high pressure system, but avoid installing an item with a high minimum rating on a low pressure system! Read our guide to water pressure to learn more.
Need more help?
Products from the same range
You may also like
Customers also bought
Related categories
We're here for you
Advice guides
-
These Are Our Favourite Kitchen Ideas 2023
Need some kitchen design inspiration? From choosing the perfect taps to new design styles, we take you through our picks for the top kitchen trends of 2023. -
Boiling Water Taps Guide
From water temperatures and pressure to cost and installation, we take you through everything you need to know about boiling water taps.