-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
Recommended extras
Hand-picked recommendations to go alongside this product
Bring a sleek, modern touch to your bathroom with this compact mini basin tap, ideal for cloakroom basins and smaller spaces. Available in elegant Gunmetal and warm Brushed Bronze finishes, it features sharp square edges for a contemporary look that complements any interior. Designed to perform reliably even at very low water pressure, this tap ensures consistent flow across all systems. The aerated spout blends air into the water stream, creating a smooth, “champagne-like” flow for a touch of everyday luxury.
Features:- Modern mini basin tap available in Gunmetal and Brushed Bronze with a matching slotted sprung waste, perfect for any smaller basin or cloakroom basin
- Brass body and zinc alloy handle providing durability, antibacterial properties and a high resistance to corrosion
- Ceramic disc technology preventing excess drips and leaks
- Aerated spout mixes air into the water to create a soft, “champagne-like” flow
- Easy-to-use single lever operation of water flow and temperature
- Minimum 0.2 bar water pressure required
- Complies with BS6920 and BSEN200 standards
- Includes matching slotted sprung waste
- 5 year manufacturer’s guarantee
| Cleaning Instructions |
|---|
| Product Code | hrb-status-mini-bsn-tap-pv |
|---|---|
| Type | Cloakroom Basin Mixers, Mono Basin Mixers |
| Brand | Harbour |
| Brand Range | Harbour Status |
| GuaranteeMore information | 5 Years |
Guarantee
Please note that these guarantees are provided by the manufacturer, and will be subject to individual exclusions, exceptions, and terms and conditions, for example avoiding abrasive bleach-based cleaning products.
If you need further info about a specific manufacturer's guarantee, please contact our team.
| Waste Type | Slotted Clicker Waste |
|---|---|
| AeratorMore information | Yes |
| Material | Brass, Zinc Alloy |
| Temperature Control | Manual |
| Cartridge TypeMore information | Ceramic Disc |
| Popular Features | Waste Included |
Tap aerators are simple but beautifully-engineered devices that save water and money without a perceived loss of pressure. These small attachments are inserted inside the end of the spout and provide a regulated, smoothed and aerated flow of water by separating a single flow into many tiny streams. These streams mix with air as they flow from the tap, meaning less water is needed to achieve the same 'feel' and performance as non-aerated taps.
They can also be purchased separately and retrofitted to most taps, or they can usually be uninstalled if not wanted. They're a great benefit on high pressure systems where the full flow of water is unnecessary, cutting your water bills and helping to reduce wastage. On lower-pressure systems they can help to improve the performance of a tap by adding air to the limited flow of water available. All-in-all, they're pretty awesome.
They can also be purchased separately and retrofitted to most taps, or they can usually be uninstalled if not wanted. They're a great benefit on high pressure systems where the full flow of water is unnecessary, cutting your water bills and helping to reduce wastage. On lower-pressure systems they can help to improve the performance of a tap by adding air to the limited flow of water available. All-in-all, they're pretty awesome.
Taps use either a ceramic disc cartridge or a rubber compression washer to control flow. Rubber washers will naturally wear down with use, and the tap handle will require more and more rotations to turn on or off. On the plus side, it's very easy to replace a rubber washer and they're available everywhere.
Ceramic disc cartridges need only a 90-degree rotation to fully open or close, and the 2 ceramic plates are incredibly hard-wearing and resilient. They're more expensive to make, but they allow for a huge range of designs, easy operation and simple maintenance if needed.
Whilst it is rare for a ceramic cartridge to need replacing, you may very occasionally need to remove and rinse the cartridge if grit or debris within the water system is preventing the 2 plates from closing properly. Much like replacing a rubber washer, this is a quick and easy job, and will ensure many years of use.
Ceramic disc cartridges need only a 90-degree rotation to fully open or close, and the 2 ceramic plates are incredibly hard-wearing and resilient. They're more expensive to make, but they allow for a huge range of designs, easy operation and simple maintenance if needed.
Whilst it is rare for a ceramic cartridge to need replacing, you may very occasionally need to remove and rinse the cartridge if grit or debris within the water system is preventing the 2 plates from closing properly. Much like replacing a rubber washer, this is a quick and easy job, and will ensure many years of use.
| Mounting Type | Deck Mounted |
|---|---|
| Shape | Square |
| Handle Type | Lever, Single Control |
| Spout Type | Fixed Spout, L-Shaped Spout, Straight Spout |
| Tap Holes | Mono |
| Style | Modern |
| Finish | Select an option first |
| Texture | Select an option first |
| Width (mm) | 46 |
|---|---|
| Height (mm) | 128 |
| Depth (mm) | 147 |
| Projection (mm) | 102 |
| Flow Rate at 0.2 Bar (l/min) | 5.2 |
|---|---|
| Flow Rate at 0.5 Bar (l/min) | 7.8 |
| Flow Rate at 1 Bar (l/min) | 10.9 |
| Flow Rate at 1.5 Bar (l/min) | 13.3 |
| Flow Rate at 2 Bar (l/min) | 15.3 |
| Flow Rate at 3 Bar (l/min) | 18.7 |
| Minimum Water PressureMore information | 0.2 |
Minimum Water Pressure
Your water pressure depends on your home's water system. It’s important to consider water pressure when buying a new tap or shower. Buying a product with a minimum water pressure that’s too high for your home will result in poor performance.
- With a combi boiler you can usually expect between 1 and 2 bar
- With a gravity system (cold water tank in attic) you may have as little as 0.1 or 0.2 bar upstairs, and perhaps 0.5 bar downstairs
- With a high pressure unvented system (hot water cylinder, no cold water tank) you will generally have between 1 and 3 bar
You can install an item with a low minimum pressure rating on a high pressure system, but avoid installing an item with a high minimum rating on a low pressure system! Read our guide to water pressure to learn more.
