-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
-
Click the image to zoom
Recommended extras
Hand-picked recommendations to go alongside this product
A regal bathroom is one that triggers memories of time ago, when magistrates stalked their opulent mansions and bathed like there was all the time in the world. And what better way to emulate this in your own bathroom than with the Burlington Anglesey Bath Shower Mixer, the perfect companion to a luxury freestanding bathtub or traditional roll-top.
It features wonderfully classic, four spoke tap heads. These are finished with white ceramic indices that indicate the hot and cold taps, and also match up with the stylishly pronounced diverter lever that changes the flow of water between the bath spout and shower handset. The spout also swivels so you don’t have it in your way when you shower.
Supplied with two Neoperl devices - a flow straighter which is for use with low water pressures and an aerator which is for use with high water pressures, this mixer was designed to deliver the following maximum flows of water, regardless of the incoming water pressure (22 litres per minute). This way you can have fabulous performance without wasting any water.
The Burlington Anglesey Deck Mounted Bath Mixer also comes with a 'S' adjuster, which allows you to position the telephone handset over the bath to ensure every last drop falls into the tub, and not onto the tap ledge. This reduces cleaning, mould and potential water ingress at the perimeter of the bath. You can install your Bath Shower Mixer with or without this feature.
The bath shower mixer includes:
Features:
Dimensions:
It features wonderfully classic, four spoke tap heads. These are finished with white ceramic indices that indicate the hot and cold taps, and also match up with the stylishly pronounced diverter lever that changes the flow of water between the bath spout and shower handset. The spout also swivels so you don’t have it in your way when you shower.
Supplied with two Neoperl devices - a flow straighter which is for use with low water pressures and an aerator which is for use with high water pressures, this mixer was designed to deliver the following maximum flows of water, regardless of the incoming water pressure (22 litres per minute). This way you can have fabulous performance without wasting any water.
The Burlington Anglesey Deck Mounted Bath Mixer also comes with a 'S' adjuster, which allows you to position the telephone handset over the bath to ensure every last drop falls into the tub, and not onto the tap ledge. This reduces cleaning, mould and potential water ingress at the perimeter of the bath. You can install your Bath Shower Mixer with or without this feature.
The bath shower mixer includes:
- Swivel spout
- Traditional ceramic telephone shower handset
- Standard cradle & 'S' adjuster to position handset over the bath
- White ceramic diverter lever
- 1200mm high-flow 'anti-kink' hose
- 3/4" deck mounting unions
- Pair of Anglesey tap handles with a four spindle head & ceramic indices
Features:
- Crafted from solid brass with polished chrome finish
- Quarter turn ceramic disc technology for improved performance & longer life span
- Spout and 'S' adjuster can be swiveled left or right and kept out of the way
- Separated controls for hot & cold supply
- 10 year guarantee
- Suitable for all water pressures: from 0.2 to 5 bar
- Supplied with flow straighter for use with low water pressure
- Supplied with anti-splash NEOPERL® aerator for use with high water pressure
- Waste not included
Dimensions:
- Width - 300mm
- Height - 503mm
- Depth - 157mm
| Cleaning Instructions |
|---|
| Product Code | AN15-QT |
|---|---|
| Type | Bath Shower Mixers, Bridge Bath Taps |
| Brand | Burlington |
| Brand Range | Burlington Anglesey |
| GuaranteeMore information | 10 Years |
Guarantee
Please note that these guarantees are provided by the manufacturer, and will be subject to individual exclusions, exceptions, and terms and conditions, for example avoiding abrasive bleach-based cleaning products.
If you need further info about a specific manufacturer's guarantee, please contact our team.
| Material | Brass |
|---|---|
| Number of Outlets | 2 Outlets |
| Temperature Control | Manual |
| Cartridge TypeMore information | Ceramic Disc |
Taps use either a ceramic disc cartridge or a rubber compression washer to control flow. Rubber washers will naturally wear down with use, and the tap handle will require more and more rotations to turn on or off. On the plus side, it's very easy to replace a rubber washer and they're available everywhere.
Ceramic disc cartridges need only a 90-degree rotation to fully open or close, and the 2 ceramic plates are incredibly hard-wearing and resilient. They're more expensive to make, but they allow for a huge range of designs, easy operation and simple maintenance if needed.
Whilst it is rare for a ceramic cartridge to need replacing, you may very occasionally need to remove and rinse the cartridge if grit or debris within the water system is preventing the 2 plates from closing properly. Much like replacing a rubber washer, this is a quick and easy job, and will ensure many years of use.
Ceramic disc cartridges need only a 90-degree rotation to fully open or close, and the 2 ceramic plates are incredibly hard-wearing and resilient. They're more expensive to make, but they allow for a huge range of designs, easy operation and simple maintenance if needed.
Whilst it is rare for a ceramic cartridge to need replacing, you may very occasionally need to remove and rinse the cartridge if grit or debris within the water system is preventing the 2 plates from closing properly. Much like replacing a rubber washer, this is a quick and easy job, and will ensure many years of use.
| Mounting Type | Deck Mounted |
|---|---|
| Finish | Chrome |
| Shape | Round |
| Handle Type | Crosshead, Lever, Triple Control |
| Spout Type | Curved Spout |
| Texture | Polished |
| Tap Holes | 2 Holes |
| Style | Traditional |
| Width (mm) | 300 |
|---|---|
| Height (mm) | 503 |
| Depth (mm) | 157 |
| Minimum Water PressureMore information | 0.2 |
|---|
Minimum Water Pressure
Your water pressure depends on your home's water system. It’s important to consider water pressure when buying a new tap or shower. Buying a product with a minimum water pressure that’s too high for your home will result in poor performance.
- With a combi boiler you can usually expect between 1 and 2 bar
- With a gravity system (cold water tank in attic) you may have as little as 0.1 or 0.2 bar upstairs, and perhaps 0.5 bar downstairs
- With a high pressure unvented system (hot water cylinder, no cold water tank) you will generally have between 1 and 3 bar
You can install an item with a low minimum pressure rating on a high pressure system, but avoid installing an item with a high minimum rating on a low pressure system! Read our guide to water pressure to learn more.
Products from the same range
You may also like
Customers also bought
Related categories
We're here for you
Advice guides
-
Bath Taps: A Complete Guide to Help You Decide
At Tap Warehouse we stock an enormous range of bath taps for you to choose from. In fact, there are just so many that we can’t even decide which our favourites actually are… We’ve tried our hardest though, and narrowed it down to some of the very best taps for all budgets and styles for you to peruse below. -
Bathroom Taps: What You Need to Know
There is a huge variety of bathroom taps out there. This guide walks you through the questions that you should be asking yourself before choosing new taps for your bathroom.
